JAX

  • Modern timeless design
  • High arch spout for easy filling of pots and vases
  • Enlarged working radius thanks to the swivel spout
  • Twin lever: ideal for low pressure water systems
  • Available inchrome, PVD steel and black matt

raw material: brass

brass

colour: PVD steel

black+matt
PVD+steel
chrome

high spout: Yes | wall mounted: No | high/low-pressure: High Pressure

Article number 526682

Find Dealer
Data & Documentation

Data sheet & Documentation

2 spray typesNo

2-handleYes

archetypeJ-shape

bridgeNo

filter mixer tapNo

flow rate at 3 bar (l/min)19.4 l

BLANCO UNIT

Our BLANCO UNIT recommendations

JAX in BLANCO UNIT

Recommendation 1
ANDANO XL 6 S-IF

Fitting Sink

BOTTON Pro 60

Fitting Waste Collector

JAX

Fitting Tab

Recommendation 2
CLASSIMO XL 6 S-IF

Fitting Sink

SELECT II Compact 60/2

Fitting Waste Collector

JAX

Fitting Tab

Care Products
Spare parts

Spare parts

Spare parts
ImageArticle numbers & descriptionsPrice
1Lever cold JAX, LAX, MAX II PVD steel complete

Art. ID: 124228

Lever cold JAX, LAX, MAX II PVD steel complete

£29.99
2Lever hot JAX, LAX, MAX II PVD steel complete

Art. ID: 124230

Lever hot JAX, LAX, MAX II PVD steel complete

£29.99
3Spacer ring f. lever JAX, LAX, MAX II LT

Art. ID: 124223

Spacer ring f. lever JAX, LAX, MAX II LT

£10.49
4Valve cover with screw LT

Art. ID: 124224

Valve cover with screw LT

£13.49
5Valve right to close 90° brass SD

Art. ID: 124292

Valve right to close 90° brass SD

£24.49
6Valve left to close 90° brass SD

Art. ID: 124293

Valve left to close 90° brass SD

£24.49
7Seal set+screw+cap PST JAX,LAX,MAX II LT

Art. ID: 124290

Seal set+screw+cap PST JAX,LAX,MAX II LT

£13.99
8Jet reg. IT M22x1 HC Laminar PST LT

Art. ID: 124229

Jet reg. IT M22x1 HC Laminar PST LT

£14.49
9Mounting Kit RIVANA

Art. ID: 402504

Mounting Kit RIVANA

£14.49
10Stabilization plate ORION/PALLAS/TERA/URANUS

Art. ID: 126945

Stabilization plate ORION/PALLAS/TERA/URANUS

£7.49
11Flex.hose 70cm ST R FI EU ½-M8x1

Art. ID: 123942

Flex.hose 70cm ST R FI EU ½-M8x1

£1.49
12Flex.hose 70cm ST B FI EU ½-M8x1

Art. ID: 123943

Flex.hose 70cm ST B FI EU ½-M8x1

£1.49
13Filter gasket for 1/2" corner valve NE

Art. ID: 124264

Filter gasket for 1/2" corner valve NE

£7.99
Additional mixer taps stabilisation 60mm

Art. ID: 513383

Additional mixer taps stabilisation 60mm

£21.99
Additional mixer taps stabilisation 75mm

Art. ID: 513384

Additional mixer taps stabilisation 75mm

Flexible sealing tape

Art. ID: 120055

Flexible sealing tape

FAQ

Frequently Asked Questions

  • Generally speaking, our mixer taps are easy-care and hygienic. This is thanks to their smooth surface, which allows hardly any dirt to settle on it. However, mixer taps do benefit from regularly cleaning. It doesn’t take much effort, but it needs to be done frequently. Take a mild cleaning agent and go over the mixer taps a few times with the soft side of a sponge. Now rub them dry with a microfibre cloth, and you’ll see that your mixer taps are back to being a stand-out feature of your kitchen once again, in just a few simple steps.

  • If your low-pressure mixer tap is dripping slightly, there’s no need to get a plumber in right away. This is completely normal. The reason is that low-pressure mixer taps are normally connected to a boiler. If you have used some warm water, cold water will flow into the boiler to be heated up. The rise in temperature means that the water in the pipe expands. As a result, the rising water pressure causes a small amount of water to be pushed into the mixer tap, where a few drops will escape.

  • Most people will need a high-pressure mixer tap in their home. This is always the case if the water is heated by the central water supply. You can tell whether applies to you if your kitchen has a wall valve for both cold and warm water pipes. You will therefore need a mixer tap that can handle the high water pressure from the pipes. Sometimes, however, your flat or house many not have a central hot water supply. In this case, the water will be heated by a boiler or flow heater. If your home has a flow heater for warm water, you will also need a high pressure mixer tap. A low-pressure mixer tap is required if your warm water is supplied via a boiler. This minimises the pressure from the water pipe and conducts the water at a much lower pressure into the boiler.

  • Our pull-out sprays make your everyday life a little easier. They allow you to get the water to the part of the sink where it is actually needed. Flexible and effective. As such, our hoses are designed for constant movement. Just make sure that the hose does not develop any kinks. This can damage it, causing it to start dripping. If the hose is no longer gliding smoothly back into the body of the tap, this doesn’t mean that you’ve done something wrong. Simply apply a little mixer tap lubricant as soon as the first signs start to show. That should do the trick. The hose will then glide back into place quickly and directly, just as it did before.

  • Imagine standing in the sunshine at the kitchen window and calmly doing the washing up. Our mixer taps make this possible. Just take a look at our detachable, lowerable or collapsible mixer taps. These three concepts allow you to open the window on the other side of your sink easily and in only a few steps.

  • A spraying mixer tap gets water everywhere, not just in the sink bowl. This is usually caused by limescale that has accumulated in the mixer tap. Instead of reaching straight for an aggressive cleaning agent, adding a little citric acid or vinegar to your cleaning water should solve the problem. To clean it, wipe the fine mesh attached to the tap outlet clean. Go over it again with a soft microfibre cloth. The trick to preventing a spraying mixer tap is to clean it regularly, so limescale doesn’t get the chance to build up.

  • Splish, splash: a dripping tap is very annoying. However, there’s no need for agitation. This is either due to limescale deposits in the mixer tap cartridge, or the seals are no longer fit for purpose. Unless you’re very adept at DIY and have a well-equipped toolbox, it’s best to call a sanitary specialist to deal with this. If you’re up to handling it yourself, clean any calcified areas of the seals or mixer tap with citric acid or vinegar. If the seal has become porous it should be replaced using the right tool. Once that’s done, everything in your kitchen will be back in order again.

other Taps

other Taps